SoftHub

Versions:

- System BIOS - 02.06.0005

- ME Firmware - 02.01.07.328

- BMC Firmware - 01.27.9958

- FRUSDR - 0.23

Changes:

- Hotfix for security hole about RtcRead.

This download is valid for the products listed below:

- Intel Server Board S4600LT2

- Intel Server Board S4600LH2

- Intel Server Board S4600LTP

- Intel Server System R2304LT2HJC

- Intel Server System R2208LT2HJC4

- Intel Server System R2304LT2HKC

- Intel Server System R2208LT2HKC4

- Intel Server System R2304LTPFJC

- Intel Server System R2304LTPFKC

- Intel Server System R2304LT2HVC

- Intel Server System R2304LH2HJC

- Intel Server System R2304LH2HKC

- Intel Server System R2208LH2HKC2

- Intel Server System R2304LHPFJC

- Intel Server System R2304LHPFKC

- Intel Server System R2208LH2HJC2

- Intel Server System R2304LT2FKCM

- Intel Server System R2304LH2FKC

- Intel Server System R2304LH2FKCM

- Intel Server Board S4600LHP

- Intel Server System R2000LTMJC

Update Procedure:

- Unzip the contents of the update package and copy all files to a folder on a USB flash drive

- Insert the USB flash drive to any available USB port on the server system to be updated

- Boot the Server to the EFI shell. This can be accessed via the <F2> BIOS setup utility during POST.

- Run the command "map -r" in the EFI shell to mount a USB flash drive formatted to use the FAT32 file system

- Run the command "fs0:" to change folders to the USB flash drive. The USB flash drive may also mount to fs1: depending on other installed devices. The number of "fs#" is dependent on the result of command "map -r"

- Change folders to the folder storing the update package files

- Run the command "Startup.nsh" to start updating all the firmware and BIOS updates

Verifying Updates:

- Reboot the system

- During POST, hit the <F2> Key when prompted to access the BIOS Setup Utility

- Hit the F9 key to load BIOS Defaults

- At the MAIN menu verify the BIOS revision is correct

- Move cursor to the SERVER MANAGEMENT Menu

- Move cursor down to the SYSTEM INFORMATION Option and hit Enter

- Verify the BMC Firmware revision is correct

- Verify the SDR revision is correct

- Verify the ME Firmware revision is correct

- Hit the F10 Key to save changes and Exit

About ME Firmware:

If you wish to apply this ME (Management Engine) Firmware version, you should first make sure that the version number matches your AMT (Active Management Technology) family, as each update is specifically developed for certain system configurations.

While this technology is mostly associated with enterprises, it can also be used by various IT administrators as well as regular users. However, bear in mind that even though other platforms might also be compatible, we do not recommend installing this release on OSes other than the specified ones.

In order to apply this package, it would be best if you carefully read and understand the instructions provided by your computer manufacturer, and perform the update only when you have completely familiarized yourself with the steps.

In addition to that, make sure you perform a system reboot after upgrading the firmware version in order to allow all changes to take effect properly.

About OS Independent BIOS:

Although installing a newer BIOS version might add new features, update various components, or improve the device’s usability, this process is very risky, so the upgrade is recommended to be performed only when it is really needed.

In addition to that, this task should be performed by someone who has the knowledge to successfully complete the installation; regular users may fulfill it at their own risk.

When it comes to applying a new version without taking into account the computer’s operating system, the most commonly used method to