SoftHub

New features:

- Edge storage recording robustness is improved with an automatic database repair feature.
- Support for the NTCIP ACAP.
- Auto-iris will be enabled after manual PTZ movement from a preset with manual iris settings.
- SNMP MIB r/w OID values are saved after reboot.
- Improved info in server report from software and hardware PoE detection/negotiation.
- Improved start-up time.
- Removed predefined stream profiles: Quality, HDTV, Balanced, Bandwidth, Mobile.
- Upgrade OpenSSL to version 1.0.2d. This version also provides support for TLS 1.2.
- Improved Axis Zipstream technology for PTZ cameras.

Corrections:

- RTSP over TCP may cause choppy video if block size is not optimized or set during video connection.
- Improved SD card recording handling.
- ONVIF users are now handled when PTZ Control Queue is enabled.
- Exposure improvements when enabling custom exposure zones
- Fine tuning of IR cut filter switch in automatic mode
- Preview window is updated when changing Video Stream settings.
- Solve network share mount failures at startup.
- Improved handling of frequent I/O triggering.
- When DST is enabled, export recordings can now be done via web interface.
- It is now possible to a select starting point when playing back a recording while using multicast and H.264.
- PullMessages now follow the ONVIF specification 9.1.2.
- Rule is now triggered on startevent/"signal raise" and not on condition.
- Users with admin permissions can edit ACAP configuration settings.
- Camera is reached through HTTPS when NAT traversal is enabled.
- Improved Privacy mask alignment.
- Improved synchronization between sound and video when having low fps and long GOV length.
- An overlay text in Live View is displayed when the camera is performing pan/tilt calibration and additional logging functions has been added
- Product is shutting down PTZ functionalities for safety reason when pan/tilt calibration failed too many times.
- Improved response performance of GetCompatibleVideoEncoderConfigurations.
- Corrected H264 payloader behaviour to now insert PPS/SPS frames before every I-frame. This will improve behavior, especially with clients that uses multicast.
- Corrected image corruption issue seen in corridor format.
- Overview map removed when PTZ controls are disabled.
- Added ACAP support for NV12 format.

UPGRADE INSTRUCTIONS

The firmware can be upgraded using AXIS Camera Management, HTTP or FTP.

AXIS Camera Management:

1. Download and install AXIS Camera Management on your computer.
2. Download the upgrade file to a directory that is accessible from your local computer if the upgrade file is not to be downloaded via Internet connection from the Axis Support pages.
3. Run AXIS Camera Management. All the Axis devices found on the local subnet (or on subnets with routers that support multicasting) are shown
in the list.
4. Select the devices that you want to upgrade with new firmware (you can
even select different models) and click the Upgrade icon.
Note: A dialog will open if some of the devices can not be configured, e.g. if the devices are not accessible.
5. The Upgrade Firmware dialog shows a list of camera models.
6. Click to locate the new firmware versions stored on your hard drive, select among already downloaded files or select to download official firmware file from Axis Support Pages (marked with Download). This needs to be done for each Axis network camera or video encoder model.
7. Click OK to start upgrading the devices.

HTTP:

1. Download the upgrade file to a directory that is accessible from your
local computer.
2. Go to the product's start page (e.g. http://192.168.0.90).
3. Click the Setup link and log in as "root" (or any other user with Administrator privileges). You must be logged in as an Administrator to
upgrade the unit.
4. Click System Options in the menu to the left.
5. Click Maintenance.
6. Click the Browse button in the Upgrade Server section.
7. Select the upgrade file you downloaded (and maybe decompressed) from our site. This file is typically named after the product and Firmware version.
8. Click the Open button.
9. Click the Upgrade button in the Upgrade Server section.
10. Wait for the flash load to complete, which may take 1-10 minutes. The upgrade procedure is in four steps:
- Step 1, Shut down: Running applications are shut down and active connections are terminated.
- Step 2, Uploading firmware: The old firmware will be erased and the new firmware will be saved. During this step, the Power LED will blink green/amber. Af