SoftHub

Changes:

- Site-to-Site VPN for a single gateway-to-gateway VPN tunnel is supported.
- Capability for separate “guest” wireless network is supported.
- Security for Access Point PIN mode in Wi-Fi Protected Setup is supported. After the wrong PIN is entered 10 consecutive times, the AP PIN mode is disabled. AP PIN mode remains disabled for 24 hours, until the device is rebooted, or until the system administrator logs in to the management interface and re-enables AP PIN mode.
- WPS push-button configuration mode is disabled by default
- Context-sensitive online help is enabled.
- When the XML command is sent with the PrivMethod of privDES, the PrivMethod is set as AES instead.
- When the Password Complexity Setting of the new password must be different than the current one setting is enabled, it is not enforced when modifying the configuration using the XML API.
- When performing a backup of a configuration file using SNMP, the user cannot use the MIB object ciscosbAdminTransferFileName to specify a filename. The default filename is used instead.
- Dependency checking for SNMP authentication/privacy fields is not thorough.
- Changing the method of remote access to the management interface between HTTP and HTTPS redirects the user to an error screen.
- Guest wireless network issues: the time limit is always 30 minutes despite configured time, and time left and hostname fields are not displayed on the observation page.
- After changing the LAN IP, an “X” option is presented that performs no action when clicked.
- The Save button on the Networking > LAN > DMZ Host page does not work.
- Port forwarding issue has been resolved.
- SNMP supports dot1dBasePortTable for OnPlus.
- IPv6 rapid deployment is supported.
- IPv6 4in6 (RFC2473) is supported.
- IPv6 over PPPoE is supported.
- IPv6 prefix delegation through DHCPv6 is supported.
- The option for advertising the router address through DHCPv6 as DNS (DNS proxy), or advertising the DNS addresses received from the SP is supported.
- The Connected Devices page supports the IPv6 NDP table.
- Port forwarding supports IPv6 addresses.
- SNMP traps support IPv6 addresses.
- The WAN status page displays information learned through DHCP from the SP, such as DNS addresses, NTP servers, and prefixes.
- IPv6 fragmentation issue.
- IPv6 shows full format.
- The Connected Devices status page only shows devices connected to the default VLAN and does not show devices connected to other VLANs.
- The Quick VPN connection shows as connected after client disconnects. In some cases, the client must manually be disconnected from the VPN before the client can reconnect.
- The refresh rate on the logging page cannot be configured.
- No log or connection status for Wireless Distribution System (WDS) is displayed.
- Clicking the Reload button on the web browser requires the user to log in again to the management interface

Installation Procedure:

- Save the downloadable package.
- Log into the router’s web user interface.
- Navigate to the firmware upgrade section of your wireless unit.
- Select the present firmware and configure your router to install this file.
- Wait as the device carries out this process.
- Reboot the unit if required.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your curre