SoftHub

Additions:

- Added “No-IP.com” to supported DDNS services.
- Clicking Help now displays the context-sensitive online help page.
- Statistics display has been revised to allow users to display data in KB, MB, GB, or TB.
- The RV110W now provides a user-configurable refresh rate for the system dashboard display.
- The RV110W now provides the ability to add Static DHCP from the DHCP Leased Clients table.

Resolved Issues:

- In the Firewall > Basic Settings page, filtering options for cookies and proxy do not work.
- The RV110W does not perform input checking on the QVPN client list when importing.
- Setting up port forwarding causes the router to freeze when using VNC.
- Default remote management login should use https and port 443.
- QVPN clients cannot access any devices behind the LAN.
- RV110W should allow a maximum of 100 static route entries.
- Changing from WPA to WPA2 security mode requires a password change.
- PPTP users can access all VLANS.
- The Cisco RV110W allows the creation of multiple subnets that overlap.
- There are no logs or status indicators for RIP.
- Incorrect SNMP option name.
- DNS lookup hint is incorrect.
- In the Wireless Statistics page, when using the Show Simplified Statistics Data option, data is shown incorrectly.
- PPTP server input fields do not check for correct input.
- After using the backup and restore functions, the default gateway is unresponsive.
- The Firewall > Access Rules page gives an error when a user deactivates and reactivates a previously-configured access rule.
- The QOS > COS page displays incorrect default settings.
- Navigating from the Time settings page gives an incorrect error.
- VLAN page displays incorrect prompt when setting the default gateway of a VLAN to one that was previously allocated.
- The PPTP client does not support Microsoft Point-To-Point Encryption (MPPE).
- The RV110W stores the WAN IP address and uses it instead of obtaining a new WAN IP address.
- Upgrading the firmware via Simple Network Management Protocol (SNMP) requires the firmware image to be renamed to code.bin.
- The Website Blocking Table on the Internet Access Policy page allows duplicate entries.
- Multicast traffic does not pass to wireless clients from LAN to WLAN.
- Some time zones are incorrect on Time Settings page of the web-based Device Manager.
- Changing VLAN subnet causes system reboot.
- Multicast traffic passes from LAN to LAN clients, but does not work from LAN to WLAN.
- WDS: WLAN fails to associate with the WAP4410N in N-Only wireless mode.
- When copying any configuration file to the startup configuration, the system reboots without warning.
- Guest user account is not disabled by default.
- When viewing logs, the oldest logs are displayed first, rather than the newest logs.
- When configuring the Firewall > Internet Access Policy, the “allow by schedule, otherwise block” option allows access after the schedule ends.
- Static DHCP pop-up message needs clarification.
- When configuring WDS links with the maximum number of peers, WDS links become unstable.
- In Wireless Security, the terminology for security key needs revision and the password needs to be masked after it is saved.
- “Set on incomplete OID” causes SNMP to lock up.
- Typographical error in French graphical user interface.
- The RV110W needs to display the gateway WAN IP address in the summary page.
- Pressing Enter on the Schedule Management pages logs out the user.
- The AP Management VLAN does not work correctly.
- Deleting a VLAN causes the LAN configuration page to display blank.
- The QVPN client cannot access LAN clients when inter-VLAN routing is enabled.
- The Setup Wizard should not display again after it has been completed.
- Message that the administrator is already logged in is shown in error.
- Checksum for the MIB needs to be provided.
- The RV110W does not handle DHCP requests from untagged packets.

Installation Procedure:

- Save the downloadable package.
- Log into the router’s web user interface.
- Navigate to the firmware upgrade section of your wireless unit.
- Select the present firmware and configure your router to install this file.
- Wait as the device carries out this process.
- Reboot the unit if required.

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it